A common type of prefabricated housing, this structure is created by joining two single-wide units at the site. The resulting size typically ranges from 20 feet to 42 feet in width and 60 feet to 90 feet in length. This translates to a living space of approximately 1,200 to 3,780 square feet.
The larger footprint allows for more spacious living areas, multiple bedrooms and bathrooms, and features often found in traditional site-built homes. The affordability, combined with the increased space, makes it an attractive housing option for families, retirees, and individuals seeking a cost-effective alternative to conventional construction.
The subsequent sections will delve into the specific aspects of these measurements, including width and length variations, factors affecting overall size, and the implications for floor plans and site preparation.
1. Width
The width of these residences directly impacts living space, structural considerations, and transport logistics. This parameter significantly affects floor plan design and compliance with local regulations. Careful evaluation of width dimensions is essential for both the manufacturer and the homeowner.
-
Interior Space and Layout
Greater width permits open-concept layouts, larger rooms, and enhanced accessibility for individuals with mobility challenges. Narrower widths often necessitate more compartmentalized designs, potentially limiting furniture arrangement and movement within the home. For example, a 40-foot wide unit allows for a more expansive kitchen and living area compared to a 24-foot wide unit.
-
Structural Integrity and Support
Width influences the load-bearing requirements of the structure. Wider units may require additional support beams or reinforcement to maintain stability during transportation and occupancy. Engineering calculations must account for the span of the roof and floor joists to ensure long-term structural integrity.
-
Transportation Restrictions and Permitting
The width of each section is a primary determinant in transportation logistics. Over-width loads necessitate special permits, escort vehicles, and adherence to specific travel routes. States and municipalities impose varying restrictions on maximum transportable widths, which can influence the availability of certain models in specific regions.
-
Zoning Regulations and Setbacks
Local zoning ordinances often dictate minimum lot sizes and setback requirements based on building width. Homeowners must verify compliance with these regulations before purchasing or installing a dwelling. Restrictions may limit the placement of wider homes on certain parcels of land.
The interplay between these facets highlights the critical importance of width as a key component of overall measurements. From interior design considerations to logistical challenges and regulatory compliance, width profoundly shapes the suitability and practicality of this housing type.
Frequently Asked Questions
The following addresses common inquiries regarding the physical size of these prefabricated dwellings.
Question 1: What are the typical width ranges for a double wide manufactured home?
Common widths typically span from 20 feet to 42 feet. However, variations can occur based on manufacturer specifications and regional building codes.
Question 2: How does the overall square footage correlate to the stated dimensions?
Square footage is calculated by multiplying the width and length. A structure measuring 24 feet by 60 feet yields 1,440 square feet of living space. This is a key factor when considering dimensions of a double wide manufactured home.
Question 3: Do transportation regulations affect available size options?
Yes. Maximum transportable width is subject to state and local regulations. Over-width loads require special permitting and may limit the feasibility of transporting certain models to specific locations.
Question 4: How do the measurements influence site preparation requirements?
Precise measurements are essential for proper site grading, foundation construction, and utility connections. Inaccurate measurements can lead to significant delays and increased costs.
Question 5: Is it possible to customize the dimensions beyond standard offerings?
Customization options vary among manufacturers. While some offer flexibility in length and width, structural limitations and transportation constraints may apply.
Question 6: How do the size impact property taxes and insurance premiums?
Generally, larger homes lead to higher property tax obligations and insurance costs, reflecting an increased valuation and potential replacement expense.
Understanding these aspects provides a foundational understanding of the significance of measurements. Careful consideration of the measurements is crucial for informed decision-making in the purchase and installation of a these homes.
The following section will examine the influence of these measurements on floor plan designs and interior layout possibilities.
Navigating the Dimensions of a Double Wide Manufactured Home
Careful consideration of the physical size is paramount for a successful purchase and installation. The following tips provide guidance on maximizing the value and suitability of this housing choice.
Tip 1: Verify Local Zoning Regulations. Compliance with local ordinances regarding minimum lot size, setbacks, and permitted uses is mandatory. Failure to adhere to these regulations can result in costly delays or legal challenges.
Tip 2: Evaluate Transportation Feasibility. The chosen size must be transportable to the intended site. Over-width loads necessitate specialized permits, which can increase costs and limit route options. Contact local transportation authorities for specific requirements.
Tip 3: Assess Site Accessibility. Ensure the delivery site can accommodate the equipment required for installation. Narrow roads, steep inclines, or overhead obstructions may necessitate additional site preparation or limit size options.
Tip 4: Optimize Floor Plan Design. The measurements influence layout possibilities. A wider structure typically allows for more open-concept designs and larger rooms. Carefully consider how the dimensions align with individual lifestyle needs and preferences.
Tip 5: Confirm Foundation Requirements. The size dictates foundation specifications. A properly constructed foundation is essential for structural integrity and longevity. Consult with a qualified contractor to ensure compliance with local building codes.
Tip 6: Budget for Site Preparation Costs. Site preparation can represent a significant portion of the overall project expense. Proper grading, utility connections, and landscaping are crucial for a successful installation and should be factored into the budget.
Tip 7: Consider Future Needs. Anticipate future space requirements. Choosing a size that accommodates potential family growth, hobbies, or home office needs can enhance long-term satisfaction.
By diligently considering these factors, individuals can make informed decisions regarding the physical size. A proactive approach ensures a smooth and successful transition into this type of housing.
The subsequent section will provide a summary of key considerations and concluding remarks on the importance of careful planning.
Conclusion
The preceding discussion has elucidated the critical importance of understanding the dimensions of a double wide manufactured home. This includes width, length, and the subsequent impact on square footage, transportation logistics, and site preparation. A thorough comprehension of these aspects is paramount for informed decision-making and successful project execution.
The physical size is not merely a set of measurements, but a determining factor in structural integrity, spatial functionality, and regulatory compliance. Prioritizing due diligence and seeking expert guidance will ensure alignment between housing needs, site constraints, and long-term investment objectives. Prudent planning is essential for realizing the potential of this cost-effective housing solution.
